Deck stairs · Live 3D

Deck Stair Calculator

Enter your deck’s height and the stair’s width. You get the number of steps, riser and tread sizes, a stringer cut sheet you can take to the saw, a 3D model, code checks and a materials list. Free, no sign-up.

3D view of the stair

Drag to orbit · Ctrl + scroll or pinch to zoom · hover a card below to find it

Stair checks pass for these inputs — confirm with your building department

Risers
5
7-3/16" each · rise 3'
Treads
4
10-1/8" run · total 3' 4-1/2"
Stringers
4
2x12 × 4' 2-1/8" · 15-1/2" o.c.
Angle
35.4°
Stride 24-1/2" (2 × rise + run)
Concrete
11 bags
80 lb · 6.4 cu ft
Estimated cost
$234
7 of 10 items priced

Your stair

Rise and width
ft
ft
Treads and risers
Boards per tread
Steps, footings & landing (advanced)

Your stair

ItemQtyYour pricePriced onCost
Stringers
Stringers — 2x12 treated2 × 10' for 4 stringers of 4' 2-1/8"Pick straight boards without large knots near the notches; see the cut sheet.2 boards20 lin ft10' board ≈ $36.65$73
Treads & risers
Tread boards — PT 5/4×64 × 10' + 1 spare for 4 treads of 2 boards5 boards50 lin ft10' board ≈ $11.65$58
Foundation
Posts — 4x4 treated1 × 8': 4 at the stringer feet (1' 0-3/16")Where a guard is required, the outer posts run up as guard posts instead — buy those longer.1 board8 lin ft8' board ≈ $10.78$11
Concrete mix — 80 lb bags6.4 cu ft: 4 footings 10" × 10" × 6"; landing 3' × 5' × 4"11 bags$66
Bearing blocks — 2x4 treated4 blocks, one under each stringer foot, from one 8' 2x41 board8 lin ft8' board ≈ $5.98$6
Hardware & fasteners
Stair-stringer connectors — Simpson LSCZ or equalOne per stringer: (8) 0.148" × 1-1/2" nails into the rim, (8) into the stringer face, (1) into its edgeStandard or supported install only (rated 625 lb or more). The nail into the stringer edge goes in the second-to-last hole.4 connectors$12
Connector nails — 0.148" × 1-1/2"17 per connector68 nails—
Deck screwsTwo per tread board at every stringer (+5%), #8 × 2-1/2" or longer68 screws$8
Structural screws — #8 × 3-1/2"(8) per bearing block, (2) per inner post to its stringer36 screws—
1/2" through-bolts with washers and nutsTwo per outer bottom post (guard posts), about 6" long4 bolts—
Estimated total (7 of 10 items priced)$234

Not included in this estimate

  • Handrails, guards and their posts
  • Fascia trim around the stringers and any skirt boards
  • Permit and inspection fees
  • Labor, tool rental, delivery and sales tax

Sample prices from one US home-center website (West Sacramento, CA store), Nov 18, 2026 — prices vary by region and week. Type your store’s prices; they stay in this browser and are shared with the deck calculator.

5 risers · 4 stringers · 11 bags
$2347/10 priced
List

Updated November 2026 · Rules from IRC 2021 R311.7 and AWC DCA 6 · How we calculate

What this calculator gives you

  • Steps — risers of equal height (the bottom one included), tread run, total run, and the stair angle; on sloped ground the landing point and the rise are solved together.
  • Stringer cut sheet — the notched outline on its 2x12, the framing-square settings, the step-off length, the bottom drop and the wood left under the notches.
  • Stringers — how many, at what spacing for your tread material, how long, and which boards to buy (two short stringers often come out of one long board).
  • Foundation — a 4x4 post and footing at each stringer foot, mid-span posts when a stringer spans more than 6', and an optional concrete landing.
  • Code check — riser and tread limits, nosing, width, open risers, the 5" stringer throat, span, handrail and guards, each with its source.

Steps for common deck heights

Two 5-1/2" boards per tread with a 1" nosing, level ground, 4' wide, wood treads:

Deck heightRisersRiser heightTreadsTotal runStringer length
1' 6"36"21' 8-1/4"2'
2'46"32' 6-3/8"2' 11-13/16"
2' 6"47-1/2"32' 6-3/8"3' 2-3/16"
3'57-3/16"43' 4-1/2"4' 2-1/8"
3' 6"67"54' 2-5/8"5' 2"
4'76-7/8"65' 0-3/4"6' 1-13/16"
5'87-1/2"75' 10-7/8"7' 4-5/8"
6'107-3/16"97' 7-1/8"9' 4-1/4"
8'137-3/8"1210' 1-1/2"12' 6-13/16"

Stringer length is the 2x12 needed per stringer, including 1" to square the ends.

How the numbers are worked out

Risers and treads

The rise from the landing to the deck surface is split into equal risers no taller than about 7-1/2" (the code maximum is 7-3/4"). The deck is the top landing, so there is one tread fewer than risers. Tread run is the board depth minus the nosing. If the ground slopes, moving the landing changes the rise, so the two are solved together.

Stringer layout

Each notch is one rise by one run, laid off with a framing square along the top edge of a 2x12. The bottom of the stringer is cut down by one tread thickness so every step, the first one included, comes out the same height. With riser boards the top seat is shortened by the riser thickness so every tread overhangs equally. DCA 6 asks for at least 5" of wood between each notch and the bottom edge; the automatic layout adds risers until it is met.

Top and bottom

Stringers hang from the deck rim on sloped hangers rated at least 625 lb. At the bottom each stringer bears on a 2x4 block fastened to a 4x4 post, and each post stands on its own 10" square, 6" thick footing at least 12" below grade and below the frost line (DCA 6 Fig. 34).

This is a planning estimate. Codes vary by city and county. Check with your building department before you build, and cut one stringer and test it against the deck before cutting the rest.

Frequently asked questions

How many steps do I need for a 3 ft deck?

A 36" rise splits into 5 risers of 7-3/16" — under the 7-3/4" maximum. The deck itself is the top landing, so you build 4 treads. With two 5-1/2" boards per tread and a 1" nosing each tread runs 10-1/8", and the stair reaches 3' 4-1/2" out from the deck.

How long should deck stair stringers be?

For a 36" rise with 10-1/8" treads, each cut stringer needs 4' 2-1/8" of 2x12 — measured along the board from the top cut to the bottom cut, plus an inch to square the ends. That is shorter than the full stair diagonal because the top of the stringer sits one riser below the deck surface. Here the 4 stringers come from 2 × 10' boards.

How many stringers does a deck stair need?

At least 3 cut stringers, and close enough for the treads: wood 5/4 and 2x treads may span 18" between cut stringers (AWC DCA 6). Composite makers set their own stair spacing — 9" for Trex Enhance, 12" for other Trex 1x6 lines and Fiberon, 8–10" for TimberTech. A 4' stair takes 4 stringers with wood treads, 5 at 12" and 7 at 9".

Should stair stringers be 2x10 or 2x12?

2x12. DCA 6 requires every stringer to be at least a 2x12, and a cut stringer must keep at least 5" of wood under each notch. A 7-3/4" rise on an 11" run leaves only about 4.9", so tall risers on deep treads fail even though the IRC allows that step; the calculator then adds a riser.

What is the 7-11 rule for stairs?

It is a rule of thumb: a 7" rise with an 11" run makes an easy stair. For decks and homes the IRC allows risers up to 7-3/4" and needs treads at least 10" deep, nosing to nosing, with a 3/4"–1-1/4" nosing. Another check is 2 × rise + run ≈ 24"–25"; this calculator shows it as the stride.

Do deck stairs need a landing at the bottom?

Yes. The IRC (R311.7.6) wants a floor or landing at the top and bottom of a stairway, at least as wide as the stair and 36" deep for a straight run, sloping no more than 2%. DCA 6 adds that the stringers must not bear on a pad or patio that is not founded below the frost line — they sit on posts with their own footings.

When does a deck stair need a handrail and guards?

A handrail is required on at least one side when the stair has 4 or more risers, 34"–38" above the line of the nosings. Open sides need a guard where the stair is more than 30" above the ground (IRC), and DCA 6 asks for a stair guard once the total rise reaches 30".

How far can a stair stringer span?

DCA 6 limits a cut 2x12 stringer to 6' measured horizontally (a solid stringer to 13' 3"). Past that, a 4x4 post under each stringer on its own footing shortens the span, or you build an intermediate landing. The calculator adds those posts to the list when they are needed.

Planning the deck too? Deck material calculator